rev. 4563c?ism?01/04 features single 3-v supply voltage high-power-added efficient power amplifier (p out typically 28 dbm) ramp-controlled output power low-noise preamplifier (nf typically 2.1 db) biasing for external pin diode t/r switch current-saving standby mode few external components package: qfn20 description the t7026 is a monolithic sige transmit/receive front-end ic with power amplifier, low-noise amplifier and t/r switch driver. it is especially designed for operation in tdma systems like dect, ieee 802.11 fhss wlan, home rf and ism proprietary radios. due to the ramp-control feature and a very low quiescent current, an external switch transistor for v s is not required. electrostatic sensitive device. observe precautions for handling. figure 1. block diagram g n d v 2 _ p a v 1 _ p a v s _ l n a v 3 _ p a _ o u t l n a _ i n p a _ i n v 2 _ p a g n d r a m p g n d p u tx/rx standby control lna pa r x _ o n l n a _ o u t g n d r _ s w i t c h s w i t c h _ o u t _ r x sige fe tx v 3 _ p a _ o u t v 3 _ p a _ o u t t7026 s w i t c h _ o u t _ t x ism 2.4 ghz front end ic t7026
2 t7026 4563c?ism?01/04 pin configuration figure 2. pinning qfn20 1 2 3 4 5 15 14 13 12 11 10 6 7 8 9 16 20 19 18 17 rx_on r_switch switch_out_rx switch_out_tx gnd_lna1 v 3 _ p a _ o u t v 3 _ p a _ o u t v 3 _ p a _ o u t g n d _ l n a 2 l n a _ i n v2_pa v2_pa gnd v1_pa nc r a m p p a _ i n v s _ l n a l n a _ o u t p u t7026 pin description pin symbol function 1 rx_on rx active high 2 r_switch resistor to gnd sets the pin diode current 3 switch_out_rx switched current output for pin diode (active in rx mode) 4 switch_out_tx switched current output for pin diode (active in tx mode) 5 gnd_lna1 ground 6 lna_in low-noise amplifier input 7 gnd_lna2 ground 8 v3_pa_out inductor to power supply and matching network for power amplifier output 9 v3_pa_out inductor to power supply and matching network for power amplifier output 10 v3_pa_out inductor to power supply and matching network for power amplifier output 11 v2_pa inductor to power supply for power amplifier 12 v2_pa inductor to power supply for power amplifier 13 gnd ground 14 v1_pa supply voltage for power amplifier 15 nc not connected 16 ramp power ramping control input 17 pa_in power amplifier input 18 vs_lna supply voltage input for low-noise amplifier 19 lna_out low-noise amplifier output 20 pu power-up active high slug gnd ground
3 t7026 4563c?ism?01/04 absolute maximum ratings stresses beyond those listed under ?absolute maximum ratings? may cause permanent damage to the device. this is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. exposure to absolute maximum rating conditions for extended periods may affect device reliability . all voltages are referred to ground (pins gnd and slug) parameters symbol value unit supply voltage pins vs_lna, v1_pa, v2_pa and v3_pa_out, no rf v s 5v junction temperature t j 150 c storage temperature t stg -40 to +125 c rf input power lna p inlna -5 dbm dbm rf input power pa p inpa 10 dbm dbm thermal resistance parameters symbol value unit junction ambient qfn20, slug soldered on pcb r thja 27 k/w operating range all voltages are referred to ground (pins gnd and slug). power supply points are vs_lna, v1_pa, v2_pa, v3_pa_out. the following table represents the sum of all supply currents depending on the tx/rx mode. parameters symbol min. typ. max. unit supply voltage pins v1_pa, v2_pa and v3_pa_out v s 2.7 3.6 4.6 v supply voltage pin vs_lna v s 2.7 3.0 5.5 v supply current tx rx i s i s 470 8 ma ma standby current pu = 0 i s 10 a ambient temperature t amb -25 +25 +70 c
4 t7026 4563c?ism?01/04 electrical characteristics test conditions (unless otherwise specified): v s = 3.6 v, t amb = 25c parameters test conditions symbol min. typ. max. unit power amplifier (1) supply voltage pins v1_pa, v2_pa and v3_pa_out v s 2.7 3.6 4.6 v supply current tx i s_tx 470 ma rx (pa off), v ramp 0.1 v i s_rx 10 a standby current standby for v ramp 0.1 v i s_standby 10 a frequency range tx f 2.4 2.5 ghz gain-control range tx gp 60 42 db power gain maximum tx pin pa_in to v3_pa_out gp 28 34 33 db power gain minimum gp -40 -17 db ramping voltage maximum tx, power gain (max), pin ramp v ramp max 1.6 1.65 1.7 v ramping voltage minimum tx, power gain (min), pin ramp v ramp min 1v ramping current maximum tx, v ramp = 1.75 v, pin ramp i ramp max 0.1 ma power-added efficiency tx pae 33 37 % saturated output power tx, input power = 0 dbm referred to pins v3_pa_out p sat 27 28 29 dbm input matching (2) tx pin pa_in load vswr < 1.5:1 output matching (2) tx pins v3_pa_out load vswr < 1.5:1 harmonics at p 1dbcp tx pins v3_pa_out 2 fo -30 dbc harmonics at p 1dbcp tx pins v3_pa_out 3 fo -30 dbc t/r-switch driver (current programming by external resistor from r_switch to gnd) switch-out current output standby, pin switch_out i s_o_standby 1a rx i s_o_rx 1a tx at 100 i s_o_100 1.7 ma tx at 1.2 k i s_o_1k2 7ma tx at 33 k i s_o_33k 17 ma tx at r switch open i s_o_r 19 ma i_switch_out_rx maximum 7ma low-noise amplifier (3) supply voltage all, pin vs_lna v s 2.7 3.0 5 v supply current rx i s 810ma supply current (lna and control logic) tx (control logic active) pin vs_lna i s 0.5 ma standby current standby, pin vs_lna i s_standby 110a frequency range rx f 2.4 2.5 ghz notes: 1. power amplifier shall be unconditionally stable, maximum duty cycle 100%, true cw operation, maximum load mismatch and duration: vswr = 8:1 (all phases) 10 s, zg = 50 , v s = 3.6 v. 2. with external matching network, load impedance 50 . 3. low-noise amplifier shall be unconditionally stable. 4. with external matching components.
5 t7026 4563c?ism?01/04 power gain rx, pin lna_in to lna_out gp 15 16 19 db noise figure rx nf 2.1 2.3 db gain compression rx, referred to pin lna_out o1db -9 -7 -6 dbm third-order input interception point rx iip3 -16 -14 -13 dbm input matching (4) rx, pin lna_in vswrin < 2:1 output matching (4) rx, pin lna_out vswrout < 2:1 logic input levels (rx_on, pu) high input level = ?1?, pins rx_on and pu v ih 2.4 v s, lna v low input level = ?0? v il 00.5v high input current = ?1?, v ih = 2.4 v i ih 40 60 a low input current = ?0? i il 0.2 a electrical characteristics (continued) test conditions (unless otherwise specified): v s = 3.6 v, t amb = 25c parameters test conditions symbol min. typ. max. unit notes: 1. power amplifier shall be unconditionally stable, maximum duty cycle 100%, true cw operation, maximum load mismatch and duration: vswr = 8:1 (all phases) 10 s, zg = 50 , v s = 3.6 v. 2. with external matching network, load impedance 50 . 3. low-noise amplifier shall be unconditionally stable. 4. with external matching components. control logic for lna and t/r-switch driver operation mode pu rx_on standby 0 0 tx 1 0 rx 1 1
6 t7026 4563c?ism?01/04 input/output circuits figure 3. internal circuitry; pa_in, v1_pa figure 4. internal circuitry; ramp, v1_pa figure 5. internal circuitry v2_pa pa_in v1_pa gnd v1_pa ramp v2_pa gnd
7 t7026 4563c?ism?01/04 figure 6. internal circuitry v3_pa_out figure 7. internal circuitry switch_out_rx, switch_out_tx, r_switch, v1_pa figure 8. internal circuitry lna_in, vs_lna v3_pa_out gnd v1_pa gnd switch_out_rx/ switch_out_tx r_switch vs_lna gnd lna_in
8 t7026 4563c?ism?01/04 figure 9. internal circuitry pu, rx_on, vs_lna figure 10. internal circuitry lna_out, vs_lna vs_lna rx_on/ pu vs_lna gnd lna_out
9 t7026 4563c?ism?01/04 package information ordering information extended type number package remarks t7026-pgs qfn20 tube t7026-pgq qfn20 taped and reeled T7026-PGP qfn20 taped and reeled
printed on recycled paper. disclaimer: atmel corporation makes no warranty for the use of its products, other than those expressly contained in the company?s standar d warranty which is detailed in atmel?s terms and conditions located on the company?s web site. the company assumes no responsibi lity for any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time wi thout notice, and does not make any commitment to update the information contained her ein. no licenses to patents or other intellectual property of atmel are granted by the company in connection with the sale of atmel produc ts, expressly or by implication. atmel?s products are not aut horized for use as critical components in life support devices or systems. atmel corporation atmel operations 2325 orchard parkway san jose, ca 95131, usa tel: 1(408) 441-0311 fax: 1(408) 487-2600 regional headquarters europe atmel sarl route des arsenaux 41 case postale 80 ch-1705 fribourg switzerland tel: (41) 26-426-5555 fax: (41) 26-426-5500 asia room 1219 chinachem golden plaza 77 mody road tsimshatsui east kowloon hong kong tel: (852) 2721-9778 fax: (852) 2722-1369 japan 9f, tonetsu shinkawa bldg. 1-24-8 shinkawa chuo-ku, tokyo 104-0033 japan tel: (81) 3-3523-3551 fax: (81) 3-3523-7581 memory 2325 orchard parkway san jose, ca 95131, usa tel: 1(408) 441-0311 fax: 1(408) 436-4314 microcontrollers 2325 orchard parkway san jose, ca 95131, usa tel: 1(408) 441-0311 fax: 1(408) 436-4314 la chantrerie bp 70602 44306 nantes cedex 3, france tel: (33) 2-40-18-18-18 fax: (33) 2-40-18-19-60 asic/assp/smart cards zone industrielle 13106 rousset cedex, france tel: (33) 4-42-53-60-00 fax: (33) 4-42-53-60-01 1150 east cheyenne mtn. blvd. colorado springs, co 80906, usa tel: 1(719) 576-3300 fax: 1(719) 540-1759 scottish enterprise technology park maxwell building east kilbride g75 0qr, scotland tel: (44) 1355-803-000 fax: (44) 1355-242-743 rf/automotive theresienstrasse 2 postfach 3535 74025 heilbronn, germany tel: (49) 71-31-67-0 fax: (49) 71-31-67-2340 1150 east cheyenne mtn. blvd. colorado springs, co 80906, usa tel: 1(719) 576-3300 fax: 1(719) 540-1759 biometrics/imaging/hi-rel mpu/ high speed converters/rf datacom avenue de rochepleine bp 123 38521 saint-egreve cedex, france tel: (33) 4-76-58-30-00 fax: (33) 4-76-58-34-80 literature requests www.atmel.com/literature 4563c?ism?01/04 ? atmel corporation 2004 . all rights reserved. atmel ? and combinations thereof are the registered tradem arks of atmel corporation or its subsidiaries. other terms and product names may be the trademarks of others.
|
